HOME

CONTACT US

SERVICE

Select-A-Charge Portable Chargers

Select-A-Charge On Board Chargers


60 Amp Chargers

100 amp chargers

 

Aircraft APU & Charger

 

Charger Controller

Fuel Gauges & Volt Meters

Load Testers

Multi Bank Chargers

No Polarity Chargers

On Board Chargers

Parallel Charger

Portable Chargers

Replacement OEM Chargers 

Series Chargers

Shunt Regulators

 

QUICKCHARGESTORE.COM

MULTI BANK CHARGERS

Battery distributors, warehouses, fleet operators, EV's, RV's, Marine

 

Not series, or parallel charging. Multi Bank chargers are independent isolated circuits that charge multiple batteries individually. Never any over or undercharging. Each circuit has it's own LED to monitor progress. Simply the best way to charge groups of batteries even if operated in a series or parallel configuration.

The OCTOPUS

The Octopus is a portable or shelf type charger with (10), 12 volt, 6 amp independent circuits. Batteries in different states of discharge can be connected, and each will receive the proper charge. No over or under charging. The Green LED blinks indicating full charge. The batteries can be left connected indefinitely with only an occasional check of water level. Model QPIE12v/6Ax10 is perfect for gel's and wet starting type batteries. Model QPAGM12v/6Ax10 is a three stage charger for AGM type batteries. Tri-color LED's indicate what stage each battery is in. The Octopus is polarity protected, and there is no sparking if the charge leads come together. In addition, more than one set of leads can be connected to any battery to increase the rate of charge in 6 amp increments.

 

          Made in U.S.A.

 

Battery capacity - (10) 12 volt, 50-100 amp hour batteries @ 20 hr. rate

 

Dimen. - H.W.D  7” x 12” x 9”

Weight - 38 lbs.

AC Input - 117v, 8 amps

Output - 12v, 6-60 amps

Warranty - 1 year

 

        PDF Operating Instructions

QPIE12v/6Ax10

 

QPAGM12v/6Ax10

 

MB Models  

 

      

(2) 12 volt 10 amp circuits                 (3) 12 volt 10 amp circuits


 

 

        

 

 

      (6) 12 volt 10 amp circuits             (12) 12 volt 10 amp circuits

 


These chargers can be mounted on board equipment, or  mounted on a shelf or wall. Each circuit is  programmable via internal dip switch to charge deep cycle wet cells, starting wet cells, gels, AGM's, and lithium Ion. Each circuit is current limited, and polarity protected. As an example, they can be connected to each battery of an electric vehicle, and since each battery is charged independent of the other, battery life can increase by at least 25% over a conventional series charger. In another example, you could attach multiple leads to one or more batteries to increase the charge rate in 10 amp multiples.

6 ft AC and DC leads. Warranty is 3 years.

                             Made in U.S.A.

MODEL DC VOLTS DC AMPS AC POWER DIMENSIONS

H.W.D. INCHES

WEIGHT LBS.

MB1210X2

12

20

117V 60HZ.

3 AMP

5.5 X 8 X 8

12

MB1210X3 12 30

117V 60HZ.

4.5 AMPS

5.5 X 8 X 11.75 18
MB1210X4 12 40 117V 60HZ.

5.5 AMPS

5.5 X 8 X 14 24
MB1210X6 12 60 117V 60HZ.

9 AMPS

5.5 X 8 X 21.5 36

MB1210X10

12

100

117V 60HZ.

15 AMPS

5.5 X 13.75 X 21.5

61

MB1210X12 12 120 117V 60HZ.

17 AMPS

5.5 X 13.75 X 21.5 73
 

                   BATTERY CAPACITY @ 20 HR. RATE  50-150 AMP HOUR

                 All models available in 230 volt 50 Hz.

PDF Operating Instructions